×
x

How to Install a Sand Fence

Sand fences, like snow fences, act as windbreaks and slow the speed of blowing particles, in this case bits of blowing sand. When the wind blows over the fence, an eddy forms behind it, causing a dune to form on the windward side of the fence.

Sand fences may be made from a variety of materials, but wooden fences remain the most popular.

Things You Will Need

  • Fencing material, wooden slat or plastic mesh
  • Steel studded T or U fence posts
  • Post hole digger
  • Hammer
  • Measuring tape
  • 2 boards for every fence post, 6 feet long by 2-by-2-inches (when using plastic fencing)
  • Wire fence ties
  • Support wire
  • Pliers
  • Wire cutters

Sand fences, like snow fences, act as windbreaks and slow the speed of blowing particles, in this case bits of blowing sand.  When the wind blows over the fence, an eddy forms behind it, causing a dune to form on the windward side of the fence.

Such fences are used to form dunes where they are wanted or to prevent sand from being blown where it is not wanted.  Sand fencing can be an effective tool to restore and stabilize dune formation along shorelines.

Sand fences also can be used in desert settings to prevent erosion and to minimize sand drift on to roads. 


Location

    If sand fences are installed incorrectly, they can trap endangered sea turtles, their nests and hatchlings. Improperly installed sand fences also can impede public access to beaches.
  1. Contact your state's Department of Natural Resources to determine whether or not there are guidelines or regulations governing the installation of sand fences in your area if you want to install a sand fence on a coastline.
  2. If the fence will be located on the water side of the primary dune, sand fences should be installed in 10-foot lengths parallel to each other and at 45 degree angles to the shore.
  3. Find the crest of the primary or frontal dune. If you will install the fence parallel to a shoreline, choose a line on the land side and not the water side of this primary dune.
  4. Planting native dune grasses later in the season helps stabilize the dunes that form near the sand fence.
  5. Do not install the fence on a wet sand beach. It will be vulnerable to waves.
  6. Wooden slats
  7. Roll out the fence material, whether wood slat or plastic mesh, the length of the site where you plan to install it.

Installation

    Water will hold the sand in place as you dig the fence post holes.
  1. Soak with water the specific sites where you dig the fence post holes. This will help prevent the soft sand from falling back into the hole as you dig. Fence posts should be 8 feet apart, except for the two end posts, which should be 6 feet from the post nearest them.
  2. Dig holes for the fence posts. For a 4 foot fence, plan to leave about 4-1/2 feet of the post above the sand, as a small gap will be left between the bottom of the fence and the surface of the sand.
  3. Place a fence post into each hole and hammer it in to secure the post before shoveling sand back into the hole. Tamp down the sand around each post before moving on to work on the next post. Again, the posts should be 8 feet apart, except for the end posts, which should be 6 feet from the nearest post.
  4. Attach the top of the fence to the top of the posts, starting at one end and working toward the other end. Tie the fence in place with a wire fence tie.
  5. Pull wood slat fences taut to at least 250 pounds per foot. Synthetic fence material should be pulled taut to manufacturer specifications.
  6. Leave a gap of 4 to 8 inches between the bottom of the fence and the top of the sand's surface.
  7. Secure the bottom of the fence to each post with wire fence ties. Secure the middle of the end posts also with fence ties. Use wire for additional strength, as needed.
  8. For synthetic fences, sandwich two 2-by-2-inch, 6-foot-long wood boards around the metal fence posts, burying the excess length of the wood beneath the sand's surface. Wire the wood securely into place at each end of the metal post and again in the middle.
  9. Tip

    Check with your Department of Natural Resources for rules and regulations governing sand fence placement in your state, particularly in coastal areas. Install sand fences in spring or early summer and plant beach grass in the fall around the fence to help stabilize dune formation.

    Warning

    Avoid installing long lengths of sand fence along public access shorelines.

Things You Will Need

  • Fencing material, wooden slat or plastic mesh
  • Steel studded T or U fence posts
  • Post hole digger
  • Hammer
  • Measuring tape
  • 2 boards for every fence post, 6 feet long by 2-by-2-inches (when using plastic fencing)
  • Wire fence ties
  • Support wire
  • Pliers
  • Wire cutters

Tips

  • Check with your Department of Natural Resources for rules and regulations governing sand fence placement in your state, particularly in coastal areas.
  • Install sand fences in spring or early summer and plant beach grass in the fall around the fence to help stabilize dune formation.

Warning

  • Avoid installing long lengths of sand fence along public access shorelines.

About the Author

Cindy Day has been writing and editing since 1977. She was an editor for "Moody Monthly" magazine, a reporter for the "South Bend Tribune" and has contributed to "Advertising Age" and "Notre Dame Magazine." Day has a Master of Science in journalism from Northwestern University's Medill School of Journalism.

Photo Credits

  • the fence image by joelcleofas from Fotolia.com
  • the fence image by joelcleofas from Fotolia.com
  • california redwood fence image by Greg Pickens from Fotolia.com
  • fence image by Photoeyes from Fotolia.com
  • beach fence image by Earl Robbins from Fotolia.com
  • brown slats image by Adrian Hillman from Fotolia.com
  • wet and dry sand image by alri from Fotolia.com